Mercedes S-Class
+ Mercedes-Benz Cars of a class S (W-140)
- Operation manual
Specifications
+ Access, protection
+ Elements of systems of safety
+ car Equipment, arrangement of devices and governing bodies
- Comfort
Independent heater
+ Receptions of operation and auxiliary systems
+ Routine maintenance
+ Engine
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ gear shifting Box
+ Avtomaticheckaya transmission
+ Coupling
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
|
Independent heater
|
|
It is not allowed to activate an independent heater in territories of filling station and in the closed rooms which have not been equipped with compulsory ventilation. |
The programmed petrol independent heater of salon enters into a standard complete set of all models besides automated central air of air. The control panel with the built-in information display is located with heater functioning in the right top corner of vertical section of the central console.
Control panel functioning of an independent heater of salon
|
|
|
1 — the Control light-emitting diode of a mode of preliminary installations (yellow)
2 — the Control light-emitting diode of activation of a heater (green)
3 — the Information display
|
|
The button allows to program to three inclusions of a heater.
By means of the button the entrance in a mode of installation of the current time, day of week and time of inclusion of a heater is made.
Updating of data in a mode of installation is made by buttons and (forward/back).
For immediate activation of a heater the button serves.
Before inclusion of a heater follows by means of buttons or on the control panel of central air to expose value of temperature to which air in salon should be heated-up.
For immediate activation of a heater press the control panel button, - the control light-emitting diode of green color built in the panel should light up. Activation of a heater occurs about 30 seconds later or at temperature drop of cooling liquid to value is lower 70°С. the maximum duration of functioning of the device makes 60 minutes. Shutdown of a heater can be made by repeated pressing of the button, - the light-emitting diode should go out.
Installation of the current time The entrance in a mode of installation of the current time is made by keeping of the pressed button, - on the screen of the display indications of hours start to blink. Updating of indications is made by means of buttons and.
|
|
The simultaneous pressing of buttons allows to translate indications of hours with a step 1 minute. |
Approximately in three seconds on the display screen in a flashing mode designation of day of week is deduced, - installation is made by means of the same buttons (and).
|
|
For installation of day of week it is necessary to translate previously the indication of hours at least to one minute. |
Installation of the moment of inclusion of a heater The design of the device allows to program to three inclusions of a heater with possibility of a choice then any of three installations.
For an entrance in a mode of installation press the button P of the control panel of a heater one, two or three times (the first, second and third inclusion respectively), - on the control panel will light up a control light-emitting diode of yellow color, and on the screen the last entered indication, for example will be deduced:
|
|
Figure 1 in the left top corner of the display designates number of programmed inclusion (a call on single pressing of the button P). |
Updating of indications is made by means of buttons and.
At first correction of value of time of inclusion is made, - the simultaneous pressing of buttons allows to change indications with a step 1 minute. Then, - day of week. As soon as designation of day of week will start to blink, press one of adjusting buttons (or) and hold it pressed during about 3 seconds. In case of need day of week can not be set, - choose designation in the form of two dashes (-).
In 20 seconds after the completion of installation time and day indication on the display will go out. The turn of the programme of the last installation remains highlighted in the left top corner of the screen. Also yellow control light-emitting diode of a mode of a preselektsiya will continue to burn.
For an exit from a preselektsiya mode (refusal of the programmed inclusion of a heater) press the button P until from the screen of the display number of program input will not disappear and the yellow control light-emitting diode will not go out.
Activation of any of entered into memory of the device of installations on the set inclusion of a heater is made also by means of the button P, - in the left top corner of the screen should the turn of the programme, and also (for 20 seconds) - the entered data will be highlighted.
If day of week was not set, the left bottom corner of the screen remains blank, for example:
At such installation activation of a heater will be daily made at 20:45.
Switching off of a heater is made If on the control panel the green control light-emitting diode burns, it is necessary to press the button, if yellow, - the button P (press until from the screen the turn of the programme and the diode will not disappear will not go out).
Browse mode of the chosen installations Press and hold pressed the button, - on the screen of the display the indication of the current time of day and day of week, for example will be deduced:
Release the button, - approximately in 3 seconds on the screen the indication of the activated mode of a preselektsiya, for example will be deduced:
In this case activation of a heater will be made according to installation of the first programmed inclusion every Saturday, in 5:30 mornings.
At last, from the screen all data, except number of the activated program inclusion of a heater will disappear:
Remote control by an independent heater DU panel of an independent heater
|
|
|
1 — the Button of activation of the transmitter
2 — the Control light-emitting diode
3 — the Aerial |
|
The remote control (DU) enters into a set of a heater.
The panel allows to activate an independent heater from distance to 1000 meters.
|
|
When giving signal from the closed room range of operation of the transmitter can be reduced.
|
Hold the DU panel the aerial up. Press the transmitter button, - the control light-emitting diode should light up. Release the button, - the diode will go out about 6 seconds during which the panel should continue to be held the aerial up later.
Activation of an independent heater will occur approximately in 30 seconds or when the temperature of cooling liquid will fall below 70°С. The maximum duration of continuous functioning of a heater makes 60 minutes.
Functioning of a heater can be suspended from car salon by a way of pressing the button, - the green control light-emitting diode on the control panel should go out.
|
|
If at a nazhimaniye on the button of the transmitter there is no operation of a control light-emitting diode, follows will replace an element of a food of the panel.
|
Replacement of an element of a food of the DU panel Replacement of an element of a food of the DU panel of an independent heater
|
|
|
1 — the Movable cover
2 — Polarity of installation of an element
|
|
Shift an access cover from the bottom party of the DU panel, take an element of a food and establish on its place new, - track for polarity observance.
Establish into place a cover.
|
|
Utilization of the used element of a food should be made with observance of requirements of norms on environmental protection!
|
General comments by instructions for use an independent heater For the purpose of economy of a charge of the storage battery avoid unreasonable inclusions of a heater, especially following one after another through short time. Disconnect a heater as soon as the salon will enough get warm.
It is necessary to mean that at heater inclusion at taken of the lock or the ignition key turned in situation 1 or 0 activation of the To/in fan occurs only after cooling liquid will be heated-up to a certain temperature.
When giving food after shutdown of an onboard food on the display screen in a flashing mode indications of day of week and time of day which should be modified first of all are deduced. Further in memory of the device installations of programmed inclusions of a heater can be brought.
Spontaneous shutdown of a green control light-emitting diode testifies to malfunction existence, - in parallel on the screen of the display F letter is highlighted, - address for the help on Mercedes-Benz car repair shop.
|
|
