Mercedes S-Class
+ Mercedes-Benz Cars of a class S (W-140)
+ Operation manual
+ Routine maintenance
+ Engine
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ gear shifting Box
+ Avtomaticheckaya transmission
- Coupling
+ Coupling
Driveshaft
+ Power shafts
- Differential
Dismantling, assembly and differential check
Dismantling and assembly of a reducer of the main transfer and adjustment of gaps of gear wheels
Determination of thickness of adjusting laying and its installation in the reducer case
Check and adjustment of a gap of a flange
Dismantling and assembly of a reducer of the main transfer and adjustment of gaps of gear wheels (model 140.28/032/O33 till 31.05.94 вып., 140.042/043/063/1 and diameter of differential of 210 mm)
Dismantling and differential assembly with automatic blocking
Replacement of the cylinder of differential with automatic blocking (models 140.028/032/033 till 31.05.94 вып. and 140.1 with a code 211a)
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
|
Dismantling and differential assembly with automatic blocking
Differential with automatic blocking Differential with automatic blocking
|
|
|
A — the Block of frictional disks with a conducted gear wheel in diameter of 185 mm
In — the Block of frictional disks with a conducted gear wheel in diameter of 210 mm |
|
Dismantling By means of a drift take a roller finger (19) and a finger of differential (16) of the case of differential (13)
|
|
|
14 — the Spherical washer
15 — Satellites
17 — Gear wheels of a drive of power shafts |
22 — the Frictional disk with a slip on the one hand
23, 23a — Frictional disks without slips
24 — Frictional disks with slips from both parties |
|
|
| 1. Fix the case of differential (13). |
|
| 2. Take a roller finger (19) and a finger of differential (16) by means of a drift from the case of differential (13). |
| 3. Establish drifts (046) in gear wheels of a drive of power shafts (17). |
|
| 4. Turn satellites (15) with spherical washers (14) in the direction to an opening and remove them. |
|
| 5. At first remove the right gear wheel of a drive of a power shaft (17) (it is shown in the established situation) with frictional disks. |
|
| 6. Remove the left gear wheel of a drive of a power shaft (17) (from a conducted gear wheel) with frictional disks. |
|
|
Assembly Fix frictional disks in the correct order on both gear wheels of a drive of power shafts (17)
|
|
|
17 — the Gear wheel of a drive of a power shaft
22 — the Frictional disk with a slip on the one hand
23, 23a — Frictional disks without slips
24 — Frictional disks with slips from both parties |
|
|
|
| 1. Fix frictional disks in the correct order on both gear wheels of a drive of power shafts (17) and carefully grease frictional disks (22) and (24) universal gipoidny transmission liquid. |
| 2. At first establish the left gear wheel of a drive of a power shaft (from a conducted gear wheel) with frictional disks, then establish the right gear wheel of a drive of a power shaft (17) with frictional disks and establish a drift (046) having paid attention of that frictional disks without slips have ears. |
|
| 3. Establish satellites (15) with spherical washers (14), using a drift (046), roll them until they will not be established in the differential case. |
|
4. Establish a differential finger by means of a drift in satellites and spherical washers.
5. Check the moment of a friction of differential. It should make 80-160 Nanometers.
|
| 6. Establish a finger of differential (16) and a roller finger (19). |
|
| 7. Take differential from a vice.
|
|
|
|
